| Specifications/ Configurator |
|
|
The Felder system cutterblock
With an 88 mm knife cutting radius, 2- or 4-knife cutterblock and the unique Felder system cutterblock technology, the planed finish reaches a new higher level!
Fifteen years ago, Felder introduced the double-sided disposable planer knife system. After each cutterblock knife change, start again with perfectly adjusted machine edged planer knives. Its much faster and more economical than the standard system.
Its mere child’s play to change the planer knives. In less than a few minutes you can change either the 2- or 4-knife cutterblock. The sharp Felder planer knives are instantly ready for action!
|
|
|
The new FELDER 700 Circular Saw Unit
Constructed completely out of cast iron, the new Felder 700 Series saw unit represents a new era of running stability and efficiency.
104 mm cutting height with a 315 mm saw blade
operates with dado tooling up to 20 mm
Electronic height adjustment with LED display
Zero point tilt
Oversized saw arbor with double bearing trunnions – Maximum motor power transfer with the Poly-V belt. The electronically balanced saw arbor with dual bearing seat system is powered via a Poly-V belt. Combined this results in an almost 100% power transmission to the saw blade
Maximum energy transfer from the large Poly-V belt bearing area
Optimal extraction with a completely enclosed, below table extraction system
Precise height adjustment via precision linear guides
High precision double-sided trunnion support system
Tilt segment “Easy-Glide”:
- High durability
- Play-free tilt
- Unaffected by dust
- Completely maintenance free
- No lubrication required
|
|
|
Circular saw shaft
The electronically balanced saw arbor with dual bearing seat system is powered via a Poly-V belt. This combination results in an almost perfect transmission of power to the saw blade.
|
|
|
To use a grooving cutter “Dado cutter”
The Felder 700 Series saw unit is fully compatible with dado tooling. Thanks to removable flanges and table insert, the Felder designed, fully adjustable dado cutters can be used.
|
|
|
Workpiece stop edge
Continuous fence for parallel cuts: any dimension is possible, the fence remains in a fixed parallel position to the saw blade. You will always have the best possible bearing surface.
|
|
|
Quick change spindle system
The advantages of the Felder quick change spindle system: Quick and easy change of spindle sizes; ability to interchange between 25, 30, 40, 50 mm, ¾’’, 1’’ and 1 ¼’’ diameter spindles; facility to insert a high speed router spindle for router bits; automatic repetition of settings for production work.
|
|
|
Tilting bracket
There is no need to remove the feeder from the machine. With minimum effort the power feeder can be tilted out of the way when necessary, and then easily returned to operational position when needed.
|
|
|
Mortising unit
Easy mortising: Easy operation with a single hand lever and safe clamping of any workpiece with an eccentric clamp.
|
|
|
Trapezoid threaded spindle
4 spindles with trapezoidal threads guarantee accurate adjustment and high weight bearing capacity on the thicknessing table. The table height adjustment guideways (A+B) also stabilize the table against lateral movement particulary in the outfeed direction during thicknessing.
|
|
|
Crosscut fence
The crosscut fence 1100 mm for crosscuts between +45° and –45°. The fence can be attached to the sliding table without the use of tools. The end stop provides you with the exact 90° position.
The bevelled mitre scale with accurate readout is visible from the operating area and thus enables exact setting of the required crosscut value.
The large crosscut fence stops are constructed in such a way that a small tongue on the stop fits perfectly into a groove on the fence. This keeps the stop firmly in place for both straight and
mitered cuts.
|
|
|
The telescopic crosscut fence
The 2600 mm long telescopic crosscut fence can be effortlessly adjusted from 90° to 45°. A mitre scale on the outrigger table allows for accurate adjustments. On request, we will fit your outrigger table with the
precision mitre pin locating system. Locate your
mitre angles accurately time and again!
|
|
|
Adjust the depth of cut.
Quick and accurate adjustment of cutting depth from the operator side of the infeed table.
|
|
|
Patented planer adjustment system
Accurate adjustment is obtained with Felder’s patented planer
adjustment system, which incorporates lateral prismatic guide rails.
|
|
|
Dual lifting planer tables
Its easy to change quickly from planing to thicknessing on your machine. 4 industrial springs are used to enable quick and easy planer table lifting.
|
|
|
Height adjustment of the thicknesser table with the handwheel
Thicknessing accuracy to one tenth of a millimeter with the use of the handwheel and its integrated digital display.
Max. Thicknessing height 254 mm.
|
|
|
Outrigger table “1100”
The outrigger table enables the user to process large, heavy work pieces. Eight rollers guide the telescopic support arm, ensuring precision and stability.
|
|
|
Precision mitre index system: exact angle precision
The “precision mitre index system” on the outrigger table of the professional model allows you to freely select preset positioning stops at increments of 5°, but also at 22.5°, by means of the index locating pin
from +45° to –45°.
|
|
|
Dust extraction hood
Heavy chip loads are no problem for the chip extraction hood due to its efficient design and large dimension.
|
|
|
Electric thicknesser table height adjustment “Power-Drive”
Turn the control switch for quick adjustment and then fine tune with the push of a button. The LED display clearly shows the thicknessing table position.
|
|
|
Electronically programmable thicknesser
table height adjustment “Digi-Drive”
Enter required dimension, press start and the thicknesser table will move accurately
to the required position. Required and actual values are shown on LED displays.
Additional optional functions, such as incremental position and four programmable
thicknesser table positions are available.
|
|
|
Scoring unit
The scoring unit for cuttings in plastic laminated panels without tear outs. Backlash free height and lateral adjustment of the scoring saw blade, drive power of the industrial scoring unit 1.0 HP.
|
|
|
Precision sliding table – with “X-Roll“ guiding system
The Felder precision sliding table has been designed to accept maximum loads while retaining its smooth operation and accuracy. The “Monoprofile“ of the sliding table and base guarantees maximum torsional strength at every temperature. Through the “X“ formation of the roller bearings the load is optimally distributed to all sides. The “X-Roll“ guiding system and other numerous outstanding details are patented. Such precision and technology earns the right to the status of “World Class“.
|
|
|
The new FELDER “700” Spindle Moulder Unit
With a completely new design, the Felder “700” spindle unit
sets new standards!
Spindle operating height of up to 115 mm
Table opening: 230 mm
Quick-change system for moulder spindle
4 Operating speeds (3500, 6500, 8000, 10,000 rpm)
Change of speed from front of machine
Fully compatible with high speed router spindle at 15,000 rpm
Rearward tilt 0° to 45°
Electronic height adjustment with LED display
High precision double-sided trunnion support system
Dovetail guidance system for height adjustment
Maximum energy transfer from the large Poly-V belt bearing area
Excellent vibration absorption from heavy cast iron unit
Tilt segment “Easy-Glide”:
- High durability
- Play-free tilt
- Unaffected by dust
- Completely maintenance free
- No lubrication required
|
|
|
High-Speed Router Spindle
The high speed router spindle is designed for router shaft diameters of Ø 6–16 mm at a running speed of 15,000 rpm.
|
|
|
Small details - Big impact!
The tilting segment on the Felder 700 series has one small but important detail: it is completely free of lubrication!
|
|
|
Tilting spindle moulder
All Felder spindle moulders tilt 90°–45° as standard.
As soon as you begin working on your machine, you’ll see that your Felder’s range of applications is much wider than you might have expected and you save a lot on tools too. Using the hand wheel causes the whole moulder spindle unit to tilt to the requested angle easily and smoothly.
|
|
|
The precision “240“ spindle fence and the large spindle opening
The “240“ spindle fence is standard equipment on the spindle moulders. The spindle fence can accommodate tooling to a maximum of 230 mm and has a fine adjustment on the spindle fence outfeed side. The integrated dust extraction connector allows for chip removal. The spindle table opening is 230 mm. That is your advantage when panel-raising – the spindle tooling can be lowered under the table.
|
|
|
Multi fine adjustment system
The MULTI-adjustment system allows quick adjustment of the moulder fencer. This time saving feature reduces setup time and the number of test cuts that are required. The whole fence can also be removed and then returned to its exact position.
- automatic repeat setting after removal of your fence
- parallel adjustments of the moulder fence
- quick and accurate adjustment
- measurement scale for depth of cut
|
|
|
Optional: electrical height adjustment with “Power-Drive”
More than 50 % of our clients now decide to take electric height adjustment for the moulder spindle.
|
|
|
Variable speed control
To optimize cutting speed for each job an optional Variable Speed Control (1500 to 11,000rpm) is available.
|
|
|
Quick change, self setting, self alligning. Complete knife change in 4 minutes!
The Felder-system cutterblock: 2- or 4-knife cutterblock, Quick and effortless knife change, Self aligning knives are perfectly set each and every time! , No resin buildup on clamping bolts, Extremely quiet operation due to the enclosed design, Excellent durability of knife edges, Cost savings due to the 2 sided
low cost knives
|
|
|
Perfect planing technology
2 Spring-loaded pressure bars prevent “chattering” of very thin workpieces during thicknessing.
|
|
|
Tenons and slots
The heavy duty Felder spindle unit ensures high precision when moulding and tennoning with heavy tooling.
|
|
|
Your Felder spindle tilts “rearward” for operational comfort and the additional following reasons.
- Safety, since there is no pinch point.
- Suitable for any workpiece size
- Problem-free power feeder application
- Impeccable machined
surface
- Optimal chip removal
|
|
|
“Power-Drive” – electronic raise/lower and tilt of the blade
“Power-Drive” gives you electronic height adjustment on the saw blade. Turn the control knob to adjust the blade height, displayed on a red LED display.
|
|
